布盒子
原來那個『洞』，還有這樣做法？！困擾我許久
一心想要那個『洞』要如何更完美
Today, I am sharing a simple project that takes just two fat quarters and some interfacing.
It's reversible too! :)
Let's get right to it, shall we?
Materials:
two fat quarters
1/2 yard of stiff fusible interfacing
contrasting or matching thread
rectangular fabric scraps (preferably matches your fat quarters and no smaller than 4x4 inches)
fabric glue
That's it!
Please note: I made two baskets so you will see the fabric interchange in some of the steps.
-Wash and press your fat quarters. Don't have fat quarters? You can simply cut a 1/2 yard of 44 inch wide fabric in half (parallel to the selvage) to get two fat quarters. Cut your half yard of interfacing in half as well so that you have two fat quarters of interfacing.
- Following the manufacturers instructions, fuse each piece of fabric with interfacing.
- Clean up the edges of your fat quarters to make everything nice and even and so that there are no frayed edges.
- Stack your two fused fat quarters and cut them again if needed so they are the same size. Sometimes, due to excessive fraying, you will end up with a slightly smaller basket (you can see a difference between the sizes of my two baskets). To help avoid this, you can buy a 1/2 yard, wash it and then cut it.
CUT YOUR CORNERS
- Cut five by five inch squares from each corner. To make sure things stay nice and even, do it while your fat quarters are still stacked together. For a reversible tote, keep cuts the same. If you only plan on having one side be the outer piece, go ahead and cut the liner piece slightly smaller. 5 1/8 x 5 1/8 inch corner squares should do fine.
- Oh and hang on to those 5x5 squares! I am sharing three simple projects using them on my blog today. Go HERE to check them out.
PREPARE CUT OUT HANDLES
- Go HERE to download my fabric handle pattern. Print and cut it out...or you can trace it from your computer screen. ;)
- Grab your scraps of fabric, I used non-matching pieces but it creates a cleaner look if you can match it to your fat quarters. Center them at the short ends of your fat quarters. Pin in place.
- Center the fabric handle pattern piece about 2.5 inches down from the top. Trace.
- Sew on the traced line.
- Snip in the middle of the handle, then cut the inside of the handle out.
- Clip the curves without cutting through the stitches, push it through the hole and press with an iron.
-Top stitch around the handle opening.
*You won't see top-stitching on the handles here because it was a change I added later.
FORM THE BASKETS
- Pin the corner edges together.
- Sew with a 1/2 inch seam allowance.
- Clip the corners and press open the seams.
COMBINE BASKETS
- Also press down the top raw edge 1/2 inch.
- Turn one basket right side out and keep the other wrong side out. Nest them together.
- Add a thin line of fabric glue around the perimeter of the wrong side of the handles and glue the baskets together at the handles. I don't anticipate I will be washing these baskets much if at all, since it will soften the interfacing, but if you need to, fabric glue holds up to machine washes.
- Pin around the perimeter of the basket.
- Top stitch around. To create a cleaner look lengthen your stitch.
- Now you have a reversible basket! You can keep it rounded like this...or...
PRESS YOUR BASKET INTO SHAPE
- Turn your iron on high with full steam and press it into a box shape. You will have to press each bottom edge and side seam several times before it takes shape.
-If ever it loses it shape, simply give it another quick press.
- If you made the basket reversible, you will have to re-press it when you switch to the other side. I do not recommend switching it too often, because it will wear the interfacing down over time.
And you're done!
It's a cute customized basket, great for storing almost anything. Craft supplies preferred. :)
A pretty solution to your organization woes.
文章標籤
全站熱搜
